Welcome to Firefly
English
Firefly Docsss
Last Updated: 2026-11-18 11:46:19

Hardware Function Usage

Debug Serial

The AIBOX-Orin Nano has an onboard Type-C Console debug serial port. No external serial module is required: just connect the host to the PC with a Type-C cable for serial debugging.

Login

There are two ways to login to AIBOX-Orin Nano, one is via Console (Debug serial), the other is via HDMI.

There are two ways to login to AIBOX-Orin Nano, one is via HDMI, the other is via Console (Debug serial).

HDMI Login

When logging in via the HDMI. The login account is nvidia, with the password also being nvidia.

Console Login (Debug Serial)

Type-C Connects to the Console port. The login account is nvidia, with the password also being nvidia.

  • Baud rate: 115200
  • Data bit: 8
  • Stop bit: 1
  • Parity check: None
  • Flow control: None

Serial parameter configuration

The AIBOX-Orin Nano uses the following serial port parameters:

  • Baud rate: 115200
  • Data bit: 8
  • Stop bit: 1
  • Parity check: None
  • Flow control: None

Using serial port debugging on Windows

Serial parameter configuration

AIBOX-Orin Nano uses the following serial port parameters:

  • Baud rate: 115200
  • Data bits: 8
  • Stop bit: 1
  • Parity: none
  • Flow Control: None

Using serial port debugging on Windows

On Windows, putty or SecureCRT is generally used. Among them, we recommend using the free version of MobaXterm. This is a powerful terminal software, which is introduced here. The usage of other software is similar.

Go here download MobaXterm:

  1. Select session as Serial.
  2. Modify Serial port to the COM port found in Device Manager.
  3. Set Speed (bsp) to 115200.
  4. Click the OK button.

Serial debugging on Linux

There are several options available on Linux:

  • minicom
  • picocom
  • kermit

The following will introduce the use of minicom.

Install minicom:

sudo apt-get install minicom

After connecting the serial cable, see what the serial device file is. The following example is /dev/ttyUSB0:

$ ls /dev/ttyUSB*
/dev/ttyUSB0

Run:

$ sudo minicom
Welcome to minicom 2.7
OPTIONS: I18n
Compiled on Jan  1 2014, 17:13:19.
Port /dev/ttyUSB0, 15:57:00
Press CTRL-A Z for help on special keys

The above prompt CTRL-A Z is the escape key, press Ctrl-a and then z to bring up the menu:

   +-------------------------------------------------------------------+
                          Minicom Command Summary                      |
  |                                                                    |
  |              Commands can be called by CTRL-A <key>                |
  |                                                                    |
  |               Main Functions                  Other Functions      |
  |                                                                    |
  | Dialing directory..D  run script (Go)....G | Clear Screen.......C  |
  | Send files.........S  Receive files......R | cOnfigure Minicom..O  |
  | comm Parameters....P  Add linefeed.......A | Suspend minicom....J  |
  | Capture on/off.....L  Hangup.............H | eXit and reset.....X  |
  | send break.........F  initialize Modem...M | Quit with no reset.Q  |
  | Terminal settings..T  run Kermit.........K | Cursor key mode....I  |
  | lineWrap on/off....W  local Echo on/off..E | Help screen........Z  |
  | Paste file.........Y  Timestamp toggle...N | scroll Back........B  |
  | Add Carriage Ret...U                                               |
  |                                                                    |
  |             Select function or press Enter for none.               |
  +--------------------------------------------------------------------+

Press O according to the prompt to enter the setting interface, as follows:

           +-----[configuration]------+
           | Filenames and paths      |
           | File transfer protocols  |
           | Serial port setup        |
           | Modem and dialing        |
           | Screen and keyboard      |
           | Save setup as dfl        |
           | Save setup as..          |
           | Exit                     |
           +--------------------------+

Move the cursor to "Serial port setup", press enter to enter the serial port setup interface, then enter the letters indicated above, select the corresponding option, and set as follows:

   +-----------------------------------------------------------------------+
   | A -    Serial Device      : /dev/ttyUSB0                              |
   | B - Lockfile Location     : /var/lock                                 |
   | C -   Callin Program      :                                           |
   | D -  Callout Program      :                                           |
   | E -    Bps/Par/Bits       : 115200 8N1                                |
   | F - Hardware Flow Control : No                                        |
   | G - Software Flow Control : No                                        |
   |                                                                       |
   |    Change which setting?                                              |
   +-----------------------------------------------------------------------+

Note: Hardware Flow Control and Software Flow Control must be set to No, otherwise it may result in failure to input.

After the setup is complete, go back to the previous menu and select Save setup as dfl to save it as the default configuration, which will be used by default in the future.

Watchdog

The device names for the external watchdog is /dev/wdt_crl, the procedure is as follows:

# Write to different fields to enable the watchdog and set the time.
# The numbers 0, 1, 2, and 3 represent 0.64s, 2.56s, 10.24s, and 40.96s, respectively.
# The letter 'e' indicates enabling the watchdog, while the letter 'd' indicates disabling it.

# Enable and set the timer for 10.24 seconds. You need to write to it once every 10.24 seconds. You can also write different numbers at any time to change the timing.
echo e >/dev/wdt_crl #Enable
echo 2 >/dev/wdt_crl #Set the timeout to 10.24 seconds.

RTC

Introduction

AIBOX-Orin Nano has an external RTC powered by a capacitor on the external motherboard, which ensures the RTC continues to run for a short period after power loss. In the kernel, it is represented as rtc0.

Interface Usage

Linux provides three user-space interfaces for interacting with the RTC. The paths are:

  • SYSFS interface: /sys/class/rtc/rtc0/
  • PROCFS interface: /proc/driver/rtc
  • IOCTL interface: /dev/rtc0

Synchronize the current system time to the RTC.

hwclock -w

SYSFS interface

You can directly use cat and echo to operate the interfaces under /sys/class/rtc/rtc0/.

For example, to view the current RTC date and time:

# cat /sys/class/rtc/rtc0/date
2024-07-10
# cat /sys/class/rtc/rtc0/time
02:36:30

PROCFS interface

To print RTC-related information:

# cat /proc/driver/rtc
rtc_time        : 02:37:00
rtc_date        : 2024-07-10
alrm_time       : 00:00:00
alrm_date       : 1970-01-01
alarm_IRQ       : no
alrm_pending    : no
update IRQ enabled      : no
periodic IRQ enabled    : no
periodic IRQ frequency  : 1
max user IRQ frequency  : 64
24hr            : yes

IOCTL interface

You can use ioctl to control /dev/rtc0。

For detailed usage instructions, please refer to document kernel-jammy-src/Documentation/admin-guide/rtc.rst 。

jtop install

sudo apt update
sudo apt install python3-pip
sudo pip3 install -U jetson-stats

Important!Important!Important

Do not use sudo apt-get upgrade and sudo apt-get dist-upgrade .
Do not use sudo apt upgrade and sudo apt dist-upgrade .

To prevent automatic upgraded :

  • Modify /etc/apt/apt.conf.d/20auto-upgrades (if this file doesn’t exist, please create it)
APT::Periodic::Update-Package-Lists "0";
APT::Periodic::Unattended-Upgrade "0";
  • Disable and stop apt-daily timers
sudo systemctl disable apt-daily.timer
sudo systemctl disable apt-daily-upgrade.timer
sudo systemctl stop apt-daily.timer
sudo systemctl stop apt-daily-upgrade.timer

nvpmodel

7W15W25WMAXN_SUPER
Jetson Orin Nano 8GBMode ID 0Mode ID 1N/AN/A
Jetson Orin Nano 8GB SUPERN/AMode ID 0Mode ID 1Mode ID 2
MAXN_SUPERMAXN10W15W20W40W
Jetson Orin NX 8GBN/AMode ID 0Mode ID 1Mode ID 2Mode ID 3N/A
Jetson Orin NX 8GB SUPERMode ID 0N/AMode ID 1Mode ID 2Mode ID 3Mode ID 4
MAXN_SUPERMAXN10W15W25W40W
Jetson Orin NX 16GBN/AMode ID 0Mode ID 1Mode ID 2Mode ID 3N/A
Jetson Orin NX 16GB SUPERMode ID 0N/AMode ID 1Mode ID 2Mode ID 3Mode ID 4

Commands

  • get power mode: sudo nvpmodel -q
  • set power mode: sudo nvpmodel -m <x>
    • <x> is the power Mode ID (for example, 0, 1, 2, 3 or 4).

GUI

  • To switch the current power mode, click the NVIDIA icon to open a dropdown menu from the icon
  • Click "Power mode" to open a submenu of power modes

Browser

sudo apt update
sudo apt install chromium-browser

If the browser fails to open after installation, please follow the steps below:

snap download snapd --revision=24724
sudo snap ack snapd_24724.assert
sudo snap install snapd_24724.snap

HDMI Audio

Settings --> Sound --> Output Device --> HDMI/ DisplayPort-Build-in Audio

Flash Images

Notice:
  • PC use X86 Ubuntu 22.04 or Ubuntu 20.04, do not use virtual machine.
  • When flashing, AIBOX-Orin Nano will format the internal storage device, please back up important data first.
  • Orin NX power supply need 12V/5A
  • Orin NX carrier board hardware at least V1.2

Download fireflyFlash.tbz2

Download Firmware --> Jetson Linux

Unzip fireflyFlash.tbz2

mkdir fireflyFlash
tar xf fireflyFlash.tbz2 -C fireflyFlash
cd fireflyFlash
sudo ./l4t_flash_prerequisites.sh

Put AIBOX-Orin Nano into Force Recovery Mode

  • Ensure that AIBOX-Orin Nano is powered off
  • Connect AIBOX-Orin Nano and PC using TypeC
  • Press and hold down AIBOX-Orin Nano Recovery-Key
  • AIBOX-Orin Nano power on
  • Release AIBOX-Orin Nano Recovery-Key
  • Check AIBOX-Orin Nano Recovery Mode
    • use lsusb comand, AIBOX-Orin Nano is in Force Recovery Mode if you see the message: Bus <bbb> Device <ddd>: ID 0955: <nnnn> Nvidia Corp.
      • <bbb> any three-digit number
      • <ddd> any three-digit number
      • <nnnn> four-digit number
        • 7523 Jetson Orin Nano 8GB
        • 7423 Jetson Orin NX 8GB
        • 7323 Jetson Orin NX 16GB

Flash

Enter these commands in the directory of fireflyFlash: ./firefly_flash.sh -d aibox

Notice: After burning, the device must be on the desktop for at least 5 minutes before it can be powered off.

On this page